MC7.T07 Superconducting RF
SUPG071
Novel materials for beam acceleration
use link to access more material from this paper's primary code
Bulk niobium is currently the standard material for constructing superconducting radio frequency (SRF) cavities for acceleration in particle accelerators. However, bulk niobium is limited, and new materials and surface treatments may allow greater performance to be reached. We present progress on novel materials and treatments for SRF cavity fabrication.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS15
About: Received: 20 May 2024 — Revised: 20 May 2024 — Accepted: 20 May 2024 — Issue date: 01 Jul 2024
Parameters and process study of copper chamber coating with niobium thin films in DC and HIPIMS modes
This study primarily investigates the parameters and processes involved in depositing Nb thin films on copper cavities under DC and HIPIMS modes. For this purpose, a high-power magnetron sputtering system was designed, conducting a total of 36 experiments. Improvement and optimization of parameters such as duty cycle (under HIPIMS mode), peak current, and bias voltage were undertaken to enhance film quality and performance metrics such as density. Surface morphology and superconducting properties of the films were characterized using SEM, XRD, Tc measurements, and other analytical methods. It was found that the Nb film deposited at a bias voltage of 100 V and a peak current of 150 A exhibited better performance. Lateral analysis of films deposited on different areas of the cavity revealed that in the DC mode, film grain sizes at the cell level were smaller with more defects, whereas in the HIPIMS mode, the niobium film exhibited finer and elongated grains, with grain sizes across various parts of the cavity being closer and defects reduced. This resulted in greater internal uniformity within the entire cavity, contributing to the enhancement of Q and E.
SUPG073
Superconducting thin films on higher order mode antennas to increase the CW performance of SRF cavities at MESA
use link to access more material from this paper's primary code
The Mainz Energy-Recovering Superconducting Accelerator (MESA), an energy-recovering (ER) LINAC, is currently under construction at the Institute for Nuclear physics at the Johannes Gutenberg-Universität Mainz, Germany. In the ER mode continues wave (CW) beam is accelerated from 5 MeV up to 105 MeV. The energy gain of the beam is provided through 2 enhanced ELBE-type cryomodules containing two 1.3 GHz 9-cell TESLA cavities each. By pushing the limits of the beam current up to 10 mA, a quench can occur at the HOM Antennas. The quench is caused through the increased power deposition induced by the electron beam in ER mode. Calculation shown that an upgrade from 1 mA to 10 mA is increasing the deposited power in the HOMs up to 3080 mW. 30% of this power will be out coupled with the HOM couplers and can be used as a thermal input. Simulations show a power limit of 95 mW which includes the power for 1 mA but is exceeded at 10 mA. A solution to increase the power limit are superconducting thin films which provides higher critical fields, temperature and currents. As candidates are Nb3Sn and NbTiN are chosen. First simulations of the power limit for coated HOM antennas are shown.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS32
About: Received: 15 May 2024 — Revised: 21 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
SUPG074
Investigation of hot-spots due to local trapped flux in niobium superconducting radiofrequency cavities
use link to access more material from this paper's primary code
One of the significant sources of residual losses in superconducting radio-frequency cavities is magnetic flux trapped during the cool-down due to the incomplete Messier effect. If the trapped vortices are non-uniformly distributed on the cavity surface, the temperature mapping revealed the “hotspots” at the location of high density of pinned vortices. Here, we performed a rf test on 1.3 GHz single cell cavity with the combination of the temperature mapping system. The temperature mapping reveled the development of the hot spots with the increase in rf field inside the cavity. When magnetic field is trapped locally on the surface of cavity, the hot-spots strength increase rapidly, showing the direct correlation of vortex induced hot spot and corresponding rf loss.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS34
About: Received: 15 May 2024 — Revised: 21 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
SUPG075
Devices and preparation methods for niobium coupon samples used to investigate high-Q mechanism
use link to access more material from this paper's primary code
A surface treatment device has been established at the Wuxi Platform, enabling chemical polishing treatment on coupon samples. Currently, several samples treated with buffered chemical polishing (BCP) have been utilized in the investigation of nitrogen doping and medium-temperature baking mechanisms. This paper presents the development process of this device along with the experimental outcomes. In the future, we plan to enhance the device to facilitate electropolishing (EP) treatment on coupon samples.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS44
About: Received: 15 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
SUPG076
Buffered chemical polishing process for SHINE 3.9 GHz cavities
use link to access more material from this paper's primary code
The linear acceleration part of the SHINE project consists of two 3rd harmonic cryogenic modules which are operating at 3.9 GHz. Each of the cryomodules consists of eight 3.9 GHz 9-cell superconducting cavities. The SHINE specifications of the 3.9 GHz cavities are Qo >2.0e+9@13.1 MV/m and maximum accelerating gradient >15 MV/m. The 3.9 GHz cavities were treated with buffered chemical polishing (BCP) baseline combined with 2-step low-temperature baking surface treatment process to meet the specifications. In order to achieve the required performance, the BCP process had been optimized at the SHINE Wuxi surface treatment platform, especially the acid ratio. Vertical tests of all 3.9 GHz bare cavities treated with the optimized BCP process showed Qo up to 3.0e+9@13.1 MV/m and maximum accelerating gradient over 20 MV/m. The optimized BCP process applied to the 3.9 GHz cavities and related vertical test results were presented in this paper.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS46
About: Received: 16 May 2024 — Revised: 19 May 2024 — Accepted: 19 May 2024 — Issue date: 01 Jul 2024
SUPG077
Decoupling of nitrogen and oxygen impurities in nitrogen doped SRF cavities
use link to access more material from this paper's primary code
The performance of superconducting radiofrequency (SRF) cavities is critical to enabling the next generation of efficient, high-energy particle accelerators. Recent developments have focused on altering the surface impurity profile through in-situ baking, furnace baking, and doping to introduce and diffuse beneficial impurities such as nitrogen, oxygen, and carbon. However, the precise role and properties of each impurity are not well understood. In this work, we attempt to disentangle the role of oxygen and nitrogen impurities through time-of-flight secondary ion mass spectrometry of niobium samples baked at temperatures varying from 75-800°C with and without nitrogen injection. From these results, we developed treatments recipe that decouple the effects of oxygen and nitrogen in doping treatments. Understanding how these impurities and their underlying mechanisms drive further optimization in the tailoring of impurity profiles for high performing SRF cavities.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS58
About: Received: 21 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
SUPG078
Microscopic understanding of the effects of impurities in low RRR SRF cavities
use link to access more material from this paper's primary code
The SRF community has shown that introducing certain impurities into high-purity niobium can improve quality factors and accelerating gradients. We question why some impurities improve RF performance while others hinder it. The purpose of this study is to characterize the impurities of niobium coupons with a low residual resistance ratio (RRR) and correlate these impurities with the RF performance of low RRR cavities so that the mechanism of impurity-based improvements can be better understood and improved upon. The combination of RF testing, temperature mapping, frequency vs temperature analysis, and materials studies reveals a microscopic picture of why low RRR cavities experience low BCS resistance behavior more prominently than their high RRR counterparts. We evaluate how differences in the mean free path, grain structure, and impurity profile affect RF performance. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS59
About: Received: 22 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
LCLS-II-HE cavity acceptance testing progress
LCLS-II-HE is an ongoing project to upgrade SLAC's superconducting linac. The upgrade will add 23 cryomodules with a total of 192 nine-cell 1.3 GHz nitrogen-doped niobium cavities. The production and qualification testing of these cavities is nearly complete. To date, they have achieved an average maximum gradient of 27.0±3.5 MV/m and an average Q0 of 3.24±0.38e+10 at the nominal operating gradient (21 MV/m). Here we present an update of the performance statistics and an outlook on the final stages of cavity qualification. We also report on issues and lessons learned during the industrial production process.
WECN3
The testing experience of the cryomodules for the ESS beam on target phase at 2 MW capability
1949
ESS is completing the installation of the first phase of operation, which will start in fall 2024 on the partial beam dump and proceed with operation on the target in 2025, after receiving the intentional neutron production license from the authorities. All modules for this operation phase, with an energy reach of 870 MeV and a power capability of 2 MW, will be tested by spring 2024. The CM performance, associated statistics and the resulting linac composition is discussed here. Testing activities for the remaining CM for the full ESS 5 MW scope will continue until mid 2026.
Paper: WECN3
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WECN3
About: Received: 16 May 2024 — Revised: 20 May 2024 — Accepted: 20 May 2024 — Issue date: 01 Jul 2024
WEPS09
Niobium-tin as a transformative technology for low-beta linacs
2709
Niobium-tin has been identified as the most promising next-generation superconducting material for accelerator cavities. This is due to the higher critical temperature (Tc = 18 K) of Nb3Sn compared to niobium (TC = 9.2 K), which leads to greatly reduced RF losses in the cavity during 4.5 K operation. This allows two important changes during cavity and cryomodule design. First, the higher Tc leads to negligible BCS losses when operated at 4.5 K, which allows for a higher frequency to be used, translating to significantly smaller cavities and cryomodules. Second, the reduced dissipated power lowers the required cryogenic cooling capacity, meaning that cavities can feasibly be operated on 5-10 W cryocoolers instead of a centralized helium refrigeration plant. These plants and distribution systems are costly and complex, requiring skilled technicians for operation and maintenance. These fundamental changes present an opportunity for a paradigm shift in how low-beta linacs are designed and operated. Fabrication challenges and first coated cavity test results are discussed.
Paper: WEPS09
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS09
About: Received: 15 May 2024 — Revised: 21 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
WEPS10
Installation and commissioning of the APS-U bunch lengthening system
2713
A new bunch lengthening cryomodule based a sin-gle-cell superconducting (SC) cavity operating at the 4th harmonic (1408 MHz) of the main RF has been installed into Argonne’s Advanced Photon Source (APS) storage ring as part of the U.S. DOE APS Up-grade project. The beam-driven system will be used to improve the Touschek lifetime by increasing the bunch length by up to several times. The 2-meter-long cryomodule is installed into one half of an APS straight section. The cavity will run at 2.1 K and pro-vide up to 1.3 MV of potential for bunch lengthening in a storage ring mode with a beam current of 200 mA evenly distributed into 48 bunches. System features include a pneumatic slow mechanical tuner and a pair of adjustable RF power couplers to adjust both the frequency and the loaded quality factor, providing a means of stabilizing the beam over a range of beam currents and fill patterns. Beam induced higher-order modes (HOMs) will be extracted along the beam axis and damped using a pair of room temperature silicon carbide absorbers. Cryogenic cooling is being provid-ed by a new 4.3 K liquid helium refrigerator combined with vacuum pumping and J-T expansion inside the cryomodule. We summarize the system features and report some results of initial cool down, testing, and measurements with beam.
Paper: WEPS10
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS10
About: Received: 15 May 2024 — Revised: 18 May 2024 — Accepted: 18 May 2024 — Issue date: 01 Jul 2024
WEPS11
X-ray measurements in a prototype superconducting radiofrequency electron gun for LCLS-II-HE project
2717
Argonne National Laboratory is collaborating with MSU, HZDR, and SLAC on the design, fabrication, and testing of a prototype superconducting radiofrequency (SRF) gun for the LCLS-II-HE upgrade at SLAC. The gun cavity is a quarter-wave resonator with a frequency of 185.7 MHz. Despite careful calibration of the cavity field probe, there are still uncertainties in the RF measurements taken to determine quality factor and field level in the cavity. One way to independently check the RF measurements is to calculate the field level from the x-ray energy spectrum generated by field emission during testing. X-ray measurements were done with a sodium iodide detector. This paper presents results of x-ray energy spectrum measurements and compares it to the RF measurements of cavity field level at 18 MV/m and 21 MV/m. Numerical simulations are also presented to understand the acceleration and dynamics of field-emitted electrons.
Paper: WEPS11
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS11
About: Received: 20 May 2024 — Revised: 22 May 2024 — Accepted: 22 May 2024 — Issue date: 01 Jul 2024
WEPS12
HOM power in the EIC crab cavity system
2720
Two types of crab cavities, one at 197 MHz and the other at 394 MHz, are designed to compensate the loss of luminosity due to a 25 mrad crossing angle at the interaction point (IR) in the Electron Ion Collider (EIC). The Higher Order Mode (HOM) damper designs of the EIC differs from the LHC designs since in the EIC the impedance budget is tighter, especially longitudinally, and in the EIC the HOM power is much higher due to the short and high intensity electron and ion beam. In this paper, HOM power in these two cavities is evaluated and optimized.
Paper: WEPS12
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS12
About: Received: 13 May 2024 — Revised: 18 May 2024 — Accepted: 18 May 2024 — Issue date: 01 Jul 2024
WEPS13
Prototype and high-power test of SiC HOM
2723
The Electron Ion Collider (EIC), to be built at BNL, is a unique high-energy, high-luminosity, polarized electron-proton/ion collider. High-Order-Mode (HOM) damping is a big challenge for EIC electron accelerators, especially for 17 single-cell 591 MHz SRF cavities in EIC Electron Storage Ring (ESR) because of its high electron beam current (up to 2.6 A). Room temperature SiC Beamline HOM absorbers (BLA) were chosen as the baseline of the HOM absorber, due to its broadband and high power capability. A SiC HOM absorber was prototyped to test a preparing process and high power handling capability. The high power test demonstrates 0.3 W/mm^2 of power handing capability by far, and we are going higher power to test its limit. This paper will present the preparing process (shrink fit, cleaning and outgassing test) and high power test results of the SIC HOM absorber prototype.
Paper: WEPS13
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS13
About: Received: 09 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS14
Progress on high power FPC development for EIC
2727
The Electron-Ion Collider (EIC) requires 34, 500 kW continuous-wave (cw), 591 MHz Fundamental Power Couplers (FPCs) to compensate the Electron Storage Ring’s (ESR) 10 MW of synchrotron radiation and other beam driven losses. This paper will describe the FPC design and fabrication status, particularly the technical challenges associated with 500 kW cw operation and the innovative design addressing this. Of important note, the RF window based on 99.5% purity alumina window was designed to be wide operating bandwidth, which makes it applicable to FPCs for the EIC’s RF systems outside of the ESR with frequencies ranging from 197 MHz-591 MHz. This results in significant savings by eliminating the need to design multiple different RF windows for the different RF systems. This paper will describe the design and prototype progress of the High Power FPC for EIC.
Paper: WEPS14
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS14
About: Received: 09 May 2024 — Revised: 23 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS15
Novel materials for beam acceleration
2730
Bulk niobium is currently the standard material for constructing superconducting radio frequency (SRF) cavities for acceleration in particle accelerators. However, bulk niobium is limited, and new materials and surface treatments may allow greater performance to be reached. We present progress on novel materials and treatments for SRF cavity fabrication.
Paper: WEPS15
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS15
About: Received: 20 May 2024 — Revised: 20 May 2024 — Accepted: 20 May 2024 — Issue date: 01 Jul 2024
Ferroelectric fast reactive tuner – technology progress and applications
In a world’s first, CERN recently tested Euclid’s prototype ferroelectric tuner with a superconducting cavity, and successfully demonstrated its microphonics compensation*. This Ferroelectric Reactive Tuner (FRT) stands out as the swiftest RF cavity tuner utilizing a ferroelectric ceramic tuning element, boasting an impressive response time below 100 ns. The implications of this advancement are substantial, potentially leading to a significant reduction in the RF power consumption of accelerators across various applications. During this presentation, we will discuss various aspects of this novel tuning technology. Topics to be covered include the development and characterization of ferroelectric materials, metallization techniques, biasing voltage supply, and the FRT designs tailored for SRF microphonic compensations. Specifically, we will introduce a magic-T configuration designed for CEBAF C100, enabling its utilization with a single RF port connected to the cavity. Additionally, we will explore potential applications for other projects such as EIC, LHC, BERLinPro, and beyond.
WEPS17
Low RF loss DC conductive ceramic for RF windows
2733
Charging of RF windows has historically been problematic, frequently resulting in damage to the window severe enough that the window needs to be replaced. Many attempts have been made to prevent charging and therefore improve window lifetime, the most successful and common of which is coating the window with titanium nitride (TiN). Surface coatings such as TiN rely on the secondary electron yield of the coating material being lower than that of the ceramic window material, reducing the number of electrons emitted from a variety of mechanisms. An alternative approach is to introduce a small amount of DC conductivity to the ceramic itself, turning the traditionally insulating window into a mildly conductive one. This allows any charge on the surface of the window to drain rather than build until a discharge happens. A magnesium titanate ceramic has been developed with a small DC conductivity and used to make RF windows. Several window assemblies have been produced and tested, including 1.3 GHz waveguide and 650 MHz coaxial designs. The results of the conductive ceramic window test program will be presented.
Paper: WEPS17
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS17
About: Received: 16 May 2024 — Revised: 20 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS19
ESS installation progresses
2736
The ESS Linac on-going installation and technical commissioning are progressing towards the first operation at 870 MeV on the beam dump in fall 2024. Four out of five DTL tanks were commissioned with beam in the normal conducting section (NCL) and a pilot installation of 1 spoke and 1 elliptical cryomodule was conducted in the superconducting (SCL) part of the ESS tunnel in spring 2023. Regarding the latter, the goal was both to demonstrate the installation sequence as well as the completion of the cryogenic distribution system (CDS) commissioning. A total of 13 spoke and 14 elliptical cryomodules (9MB + 5HB) are being installed. Overall, 30 elliptical cryomodules will be necessary to allow the 5 MW potential power after the target commissioning. The CM test plan along with the installation of the necessary RF power stations up to the 2 MW stage for the first project phase is advancing well.
This contribution will report on the deliveries from the In-kind partners, SRF activities at the ESS test stands including the resolution of non-conformities and focus on the installation and technical commissioning of the linac components.
Paper: WEPS19
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS19
About: Received: 20 May 2024 — Revised: 21 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS20
Field emission experience, statistics and challenges with ESS elliptical cryomodules
2739
ESS elliptical cryomodules, CEA-INFN-STFC in-kind contribution, undergo site acceptance test at ESS Lund Test Stand (TS2). Here the Field Emission operation experience, modules performances statistics and limiting mechanism, diagnostics equipment and analysis tool are described. High energy field emission and dose rate operational challenges and long-term superconducting LINAC operational strategy are described.
Paper: WEPS20
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS20
About: Received: 19 May 2024 — Revised: 23 May 2024 — Accepted: 24 May 2024 — Issue date: 01 Jul 2024
WEPS21
Coupler HV bias studies on ESS elliptical cavities
2743
We study the effects of high voltage DC bias on the fundamental power couplers of the ESS elliptical SRF cavities. These tests were carried out at the TS2 facility, where cryomodule acceptance and characterization tests are carried out. We present the observed effects of positive and negative bias field on multipacting in the RF couplers, as well as the implications for operation in the ESS linac.
Paper: WEPS21
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS21
About: Received: 17 May 2024 — Revised: 18 May 2024 — Accepted: 18 May 2024 — Issue date: 01 Jul 2024
Development of plasma processing for coaxial cavity cryomodules
Several groups have demonstrated that plasma processing can help to mitigate degradation of the performance of superconducting radio-frequency cavities. Plasma processing provides an alternative to removal of cryomodules from the accelerator for refurbishment. Studies of plasma processing for quarter-wave resonators (QWRs) and half-wave resonators (HWRs) are underway at FRIB, where a total of 324 such resonators are presently in operation. Plasma processing tests were done on several QWRs using the fundamental power coupler (FPC) to drive the plasma. Driving the plasma with a higher-order mode (HOM) shows promise, as it allows for less mismatch at the FPC. Before-and-after cold tests showed a significant reduction in field emission X-rays with judicious application of plasma processing. The first attempt at plasma processing of FRIB QWRs in a cryomodule is planned for December 2023/January 2024. A repeat bunker test of the cryomodule is planned to assess the results.
WEPS23
First conduction cooled photoinjector status
2747
SRF photoguns become a promising candidate to produce highly stable electrons for UEM/UED applications because of the ultrahigh shot-to-shot stability compared to room temperature RF photoguns. SRF technology was prohibitively expensive for industrial use until two recent advancements: Nb3Sn and conduction cooling. SRF gun can provide a CW operation capability while consuming only 2W of RF power which eliminates the need of an expensive high power RF system and saves a facility footprint. Euclid is developing a continuous wave (CW), 1.5-cell, MeV-scale SRF conduction cooled photogun operating at 1.3 GHz. We aim for generation of the first beam in 2024. In this paper, we present the most up-to-date progress including results of the first cool down of the gun-cavity in the newly developed conduction cooled cryomodule and LLRF system development.
Paper: WEPS23
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS23
About: Received: 17 May 2024 — Revised: 21 May 2024 — Accepted: 22 May 2024 — Issue date: 01 Jul 2024
Development of superconducting RF cavity in traveling-wave regime at Fermilab
Niobium Superconducting RF (SRF) cavities have a theoretical peak magnetic field which limits the accelerating field to 50-60 MV/m. Presently, all SRF cavities operate in a Standing Wave (SW) resonance field in which particles experience an accelerating force alternating from zero to peak. In contrast, a resonance field in Traveling Wave (TW) mode propagates along with a structure, so particles in such field can experience a constant acceleration force and could have higher energy gain than that of SW mode. This phenomenon is defined by the cavity’s transit time factor, T. A TW structure proposed in an early study achieves T ~0.9, suggesting an increase in acceleration per structure by more than 20% compared to a SW structure (T ~0.7). The early stages of developments had been funded by several SBIR grants to Euclid Techlabs and completed in collaboration with Fermilab through a 1-cell prototype and a proof-of-principle 3-cell TW cavity. It demonstrated the TW resonance excitation at room temperature in the “as-fabricated” 3-cell structure. Here we report recent progresses and the first cryogenic testing of the 3-cell TW cavity in 2 K liquid helium at Fermilab.
First high-Q treatments for FCC 800 MHz 5-cell elliptical cavities
Development towards the FCC-ee "Z" machine requires optimization of sub-GHz elliptical cavities for high-gradient and high-Q operation, both in pulsed and CW mode, for application in the booster and collider portions. Previous development work validated the proposed 800 MHz 5-cell elliptical RF design, showing reasonable performance after EP treatment. However, the stringent high-Q (3.8e+10) and high-gradient (24 MV/m) goals of the FCC machine cavities will require further development, relying on advanced surface processing techniques developed at 1.3 GHz such as N-doping or medium-temperature furnace baking. We report the results of the first applications of these techniques to the 5-cell prototype 800 MHz elliptical cavity.
WEPS26
Results from extended range SRF cavity tuner tests for LCLS-II-HE
2751
The LCLS-II HE superconducting linac can produce multi-energy beams by supporting multiple undulator lines simultaneously. This could be achieved by using the cavity SRF tuner in the off-frequency detune mode. This off-frequency operation method was tested in 8 cryomodules at Fermilab at 2 K. In all the tests the tuners successfully achieved a frequency shift of -565±80 kHz from the 1.3 GHz value. This study discusses the cavity frequency during each stage of assembly from the cryomodule string to when they are finally tested at 2 K. Monitoring the cavity frequency from this initial stage contributed in reaching this large frequency shift. The specific procedures of tuner setting during assembly will be presented.
Paper: WEPS26
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS26
About: Received: 14 May 2024 — Revised: 20 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
WEPS27
HPR and plasma processing of a superconducting 360 MHz CH cavity
2754
Goethe University (GU), Gesellschaft für Schwerionenforschung (GSI) and Helmholtz Institut Mainz (HIM) work in collaboration on the Helmholtz Linear Accelerator (HELIAC). A new superconducting (SC) continuous wave (CW) high-intensity heavy ion linear accelerator (Linac) will provide ion beams with a maximum duty factor up to beam energies of 7.3 MeV/u. The acceleration voltage will be provided by SC Crossbar H-mode (CH) cavities, developed by the Institute for Applied Physics (IAP) at GU. Preparation methods were investigated to increase their performance. High-pressure rinsing (HPR) with ultra-pure water was performed at HIM and recovered the maximum electric field of a 360 MHz 19-cell CH cavity from Ea = 1.6 MV/m to Ea = 8.4 MV/m. This result exceeds the prior highest electric field observed of Ea = 7 MV/m by 20%. The effect of helium processing has been subsequently investigated. The cavity has been processed for a total of 2 hours at a cavity pressure of 5e-5 mBar. The performance measurement showed promising results, with an increase in maximum gradient and a change in Q-slope behavior. Further tests of helium processing concerning the reproducibility, longevity, and optimization of the observed effects are scheduled at IAP.
Paper: WEPS27
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS27
About: Received: 12 May 2024 — Revised: 19 May 2024 — Accepted: 19 May 2024 — Issue date: 01 Jul 2024
WEPS28
Study of the generalized electron emission theory in a superconducting cavity
2757
Research is being conducted on field emission, thermionic emission, generalized electron emission, and electron emission from superconducting cavities. Generalized electron emission theories, which encompass field emission and thermionic emission, are currently under investigation. In field emission, electrons are emitted from metals due to a strong local electric field, while in thermionic emission, electrons are emitted due to high local temperatures. Field emission is being explored in relation to dimensions, and thermionic emission is likewise examined as a function of dimensions. The distribution of the electric field is illustrated over surface curvature. Furthermore, field emission characteristics are specifically analyzed within the context of superconducting RF cavities.
Paper: WEPS28
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS28
About: Received: 11 May 2024 — Revised: 18 May 2024 — Accepted: 18 May 2024 — Issue date: 01 Jul 2024
WEPS32
Superconducting thin films for higher order mode antennas to increase the CW performance of SRF cavities at MESA
2760
The Mainz Energy-Recovering Superconducting Accelerator (MESA), an energy-recovering (ER) LINAC, is currently under construction at the Institute for Nuclear physics at the Johannes Gutenberg-Universität Mainz, Germany. In the ER mode continues wave (CW) beam is accelerated from 5 MeV up to 105 MeV. The energy gain of the beam is provided through 2 enhanced ELBE-type cryomodules containing two 1.3 GHz 9-cell TESLA cavities each. By pushing the limits of the beam current up to 10 mA, a quench can occur at the HOM Antennas. The quench is caused through the increased power deposition induced by the electron beam in ER mode. Calculation shown that an upgrade from 1 mA to 10 mA is increasing the deposited power in the HOMs up to 3080 mW. 30% of this power will be out coupled with the HOM couplers and can be used as a thermal input. Simulations show a power limit of 95 mW which includes the power for 1 mA but is exceeded at 10 mA. A solution to increase the power limit are superconducting thin films which provides higher critical fields, temperature and currents. As candidates are Nb3Sn and NbTiN are chosen. First simulations of the power limit for coated HOM antennas are shown.
Paper: WEPS32
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS32
About: Received: 15 May 2024 — Revised: 21 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS33
Impact of medium temperature heat treatment on flux trapping sensitivity in SRF cavities
2764
The effect of mid-T heat treatment on flux trapping sensitivity was measured on several 1.3 GHz single cell cavities subjected to vacuum annealing at temperature of 150 - 400 $^\circ$C for a duration of 3 hours. The cavity was cooldown with residual magnetic field $\sim$0 and $\sim$20 mG in the Dewar with cooldown condition of full flux trapping. The quality factor as a function of accelerating gradient was measured. The results show the correlation between the treatment temperature, quality factor, and sensitivity to flux trapping. Sensitivity increases with increasing heat treatment temperatures within the range of (200 - 325 $^\circ$C/3h). Moreover, variations in the effective penetration depth of the magnetic field and the density of quasi-particles can occur, influencing alterations in the cavity's electromagnetic response and resonance frequency.
Paper: WEPS33
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS33
About: Received: 13 May 2024 — Revised: 23 May 2024 — Accepted: 24 May 2024 — Issue date: 01 Jul 2024
WEPS34
Investigation of hot-spots due to trapped flux in niobium superconducting radiofrequency cavities
2768
One of the significant sources of residual losses in superconducting radio-frequency cavities is magnetic flux trapped during the cool-down due to the incomplete Messier effect. If the trapped vortices are non-uniformly distributed on the cavity surface, the temperature mapping revealed the “hotspots” at the location of high density of pinned vortices. Here, we performed a rf test on 1.3 GHz single cell cavity with the combination of the temperature mapping system. The temperature mapping reveled the development of the hot spots with the increase in rf field inside the cavity. When magnetic field is trapped locally on the surface of cavity, the hot-spots strength increase rapidly, showing the direct correlation of vortex induced hot spot and corresponding rf loss.
Paper: WEPS34
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS34
About: Received: 15 May 2024 — Revised: 21 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
WEPS37
REBCO sample testing at high power X-band
2772
SRF materials such as niobium have been extremely useful for accelerator technology but require low temperatures operation < 9 K. The development of high temperature superconductors (HTS) is promising due to their to their high critical temperature 89.5 K. This work intends to determine the high-power RF performance of such materials at X-band (11.424 GHz). Two kinds of REBCO coatings (thin film deposition and soldered tapes) on a copper substrate were tested. Testing was done in a hemispherical TE mode cavity due to its ability to maximize the magnetic field on the sample and minimize the electric field. We will report conductivity vs temperature at low and high power. We determine the quench field in the REBCO sample and explain the evidence which shows that the quenching is most likely due to reaching the critical current and not due to average applied heat load for powers up to 1.6 kW.
Paper: WEPS37
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS37
About: Received: 14 May 2024 — Revised: 19 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
WEPS38
Upgraded multiprobe sample inserts for thin film SRF cavity developments
2775
Optimisation of thin film (TF) coating parameters for producing SRF cavities requires rapid testing of superconducting properties. A dedicated multiprobe facility built at Daresbury Lab, based on a liquid He free cryocooler, allows such measurements to be performed. The facility has vacuum tubular inserts where the sample probe is loaded and cooled with He gas. The experimental inserts were either newly built or upgraded: (1) A DC resistance experiment allows measurements of critical temperature (Tc) and residual resistance ratio (RRR) on non-conductive substrates (e.g. sapphire). A newly designed insert allows better temperature control and easier sample change. (2) A new insert for magnetic field measurements of Tc on both conductive and non-conductive substrates. (3) An existing insert for planar magnetic field penetration experiments was significantly redesigned. It operates at lower temperatures (> 5.5 K), parallel magnetic fields < 600 mT, increased sensitivity, and enables measurements of field of first flux penetration (Bfp) and Tc on various substrates: copper and sapphire, the latter of which was impossible to measure with an older design.
Paper: WEPS38
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS38
About: Received: 15 May 2024 — Revised: 19 May 2024 — Accepted: 19 May 2024 — Issue date: 01 Jul 2024
WEPS39
V₃Si: an alternative thin film material for superconducting RF cavities
2779
Superconducting materials, like V3Si, NbN, NbTiN and Nb3Sn, are potential alternatives to Nb for next generation thin film SRF cavities. In comparison to the Nb, their relatively high Tc could allow for operation at higher temperatures (≥ 4 K) and the higher critical field could lead to for higher accelerating gradients. We investigate optimum deposition parameters and substrates for V3Si, using single target physical vapor deposition (PVD). We report on the superconducting properties such as Tc and surface resistance using RRR and low power RF, stoichiometry using RBS, SIMS, XPS and EDX and surface quality using AFM and white light interferometry.
Paper: WEPS39
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS39
About: Received: 15 May 2024 — Revised: 19 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS40
T-Mapping diagnostic system for vertical test of SHINE superconducting cavity
2782
T-mapping diagnostic system is an indirect method to detect the internal surface of superconducting cavity during vertical testing. When superconducting cavity is powered, T-Mapping can detect the thermal instability and thermal collapse caused by defects. The goal of the project is to develop temperature detection devices that are highly accurate and easy to install. The development of the equipment plays a supporting role in the production of superconducting cavity, and can intuitive feedback the defects in the machining assembly, which is conducive to the improvement of the processing technology.
Paper: WEPS40
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS40
About: Received: 14 May 2024 — Revised: 21 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
WEPS41
Design, construction and operation of a surface-treatment platform for SHINE superconducting cavities
2785
The SHINE project requires more than six hundred 1.3GHz cavities and sixteen 3.9GHz cavities for the superconducting accelerator. These cavities are from both domestic and foreign companies. The cavities fabricated in domestic companies requires correspond-ing capacity of surface-treatment. For the R&D of surface-treatment technology and mass production of SRF cavities, we have been constructing a new surface-treatment platform near Shanghai for SHINE project. In this paper, we report the design, construction, commissioning and operation of this platform.
Paper: WEPS41
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS41
About: Received: 15 May 2024 — Revised: 16 May 2024 — Accepted: 17 May 2024 — Issue date: 01 Jul 2024
WEPS42
Cryomodules development for SHINE project
2788
SHINE project requires about 75 cryomodules with superconducting radio-frequency cavities to accelerate the beam to 8 GeV. Key components, technologies of cryomodule have been developing through prototypes and pre-series cryomodules. Up to now, several sets of cryomodule with high-Q cavities have been assembled and tested. We present the development status of SHINE cryomodules, including prototype cryomodules and the first ones for project.
Paper: WEPS42
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS42
About: Received: 15 May 2024 — Revised: 17 May 2024 — Accepted: 17 May 2024 — Issue date: 01 Jul 2024
Cavity and cryomodule test stands in SHINE
The SC Linac of SHINE (Shanghai HIgh repetition rate XFEL aNd Extreme light facility) comprises 79 cryomodules housing 609 1.3 GHz TESLA type superconducting cavities (SCCs), and 16 3.9 GHz SCCs. These SCCs and cryomodules should be tested in ATH (cryomodule Assembly and Test Hall) at SSRF (Shanghai Synchrotron Radiation Facility) campus. Four VTFs (SCC Vertical Test Facility) and four HTFs (Cryomodule Horizontal Test Facility) will undertake the vertical test of these SCCS and horizontal test of cryomodules. The status and future plan of these test stands will be shown.
WEPS44
Devices and preparation methods for niobium coupon samples used to investigate high-Q mechanism
2791
A surface treatment device has been established at the Wuxi Platform, enabling chemical polishing treatment on coupon samples. Currently, several samples treated with buffered chemical polishing (BCP) have been utilized in the investigation of nitrogen doping and medium-temperature baking mechanisms. This paper presents the development process of this device along with the experimental outcomes. In the future, we plan to enhance the device to facilitate electropolishing (EP) treatment on coupon samples.
Paper: WEPS44
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS44
About: Received: 15 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS45
Development of a TE-mode sample host cavity
2795
In order to study the radio-frequency performance of superconducting materials at cryogenic temperature, we developed a TE-mode 3.9 GHz sample host cavity with a spherical bottom shape. A 11.5 cm diameter flat sample plate is enabled to attach to the cavity, with 9 cm diameter central area exposed to the RF field. In this paper, the design, fabrication and vertical test results of the sample host cavity will be presented.
Paper: WEPS45
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS45
About: Received: 15 May 2024 — Revised: 18 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS46
Buffered chemical polishing process for SHINE 3.9 GHz cavities
2798
The linear acceleration part of the SHINE project consists of two 3rd harmonic cryogenic modules which are operating at 3.9 GHz. Each of the cryomodules consists of eight 3.9 GHz 9-cell superconducting cavities. The SHINE specifications of the 3.9 GHz cavities are Qo >2.0e+9@13.1 MV/m and maximum accelerating gradient >15 MV/m. The 3.9 GHz cavities were treated with buffered chemical polishing (BCP) baseline combined with 2-step low-temperature baking surface treatment process to meet the specifications. In order to achieve the required performance, the BCP process had been optimized at the SHINE Wuxi surface treatment platform, especially the acid ratio. Vertical tests of all 3.9 GHz bare cavities treated with the optimized BCP process showed Qo up to 3.0e+9@13.1 MV/m and maximum accelerating gradient over 20 MV/m. The optimized BCP process applied to the 3.9 GHz cavities and related vertical test results were presented in this paper.
Paper: WEPS46
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS46
About: Received: 16 May 2024 — Revised: 19 May 2024 — Accepted: 19 May 2024 — Issue date: 01 Jul 2024
WEPS48
Comparison on the superconducting properties of Nb and NbTiN thin films produced by both HiPIMS and bipolar HiPIMS
2802
Most superconducting thin films found on SRF cavity are generally produced through magnetron sputtering using niobium (Nb) as target. Yet, this technique can still be improved as the resulting film lack in efficiency. Alternative materials such as NbTiN could potentially be used with significant improvement compared to pure Nb films. Here, we report the use of both high-power impulse magnetron (HiPIMS) and bipolar HiPIMS to produce superconducting thin films, with a particular attention on the optimal conditions to enhance the film growth highly dependent on the pressure and power conditions. We used both mass spectroscopy and optical emission spectroscopy to analyze the plasma chemistry providing information on the mass/energy of the ions formed.
Paper: WEPS48
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS48
About: Received: 15 May 2024 — Revised: 18 May 2024 — Accepted: 19 May 2024 — Issue date: 01 Jul 2024
WEPS49
Tailoring the production of Nb superconducting films for SRF cavities: mass/energy spectroscopy and film characterisation
2806
SRF cavities are commonly coated with superconducting materials (e.g., niobium) using magnetron sputtering. In this process, various power supplies are employed such as DC, pulsed DC or HiPIMS. The sputtered ions are ejected from the target to the cavity or sample surface with an energy dependent on the power conditions and pressure range. In this study, we investigated the efficiency of such deposition by tracking the mass and energy of the main ions produced (e.g., Kr+, Kr2+, Nb+, Nb2+) using mass spectroscopy. We report the optimal conditions suitable to enhance both ions energy and film growth by comparing to power supplies (DC and HiPIMS), for different pressure conditions ranging from 1e-3 mbar to 1e-1 mbar. To support the gas phase analysis, niobium films were produced on copper substrate and the film structured was analysed by SEM.
Paper: WEPS49
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS49
About: Received: 15 May 2024 — Revised: 19 May 2024 — Accepted: 19 May 2024 — Issue date: 01 Jul 2024
WEPS50
Progress on the autonomous event detection system for the laser particulate counter
2810
Field emission is one of the most important issues that limits the performance of the superconducting radio fre-quency (SRF) systems and leads to SRF cavity trips at the Continuous Electron Beam Accelerator Facility at Jeffer-son Lab. Studies have confirmed that particulates are the dominant source of field emitters and the particulates can be transported into a cavity from other parts of the accel-erator. To monitor the transportation of the particulates, a prototype of a novel, non-invasive laser particulate coun-ter (LPC) has been developed and tested. Experiments have been done to validate the capability of the LPC. We are developing autonomous event detection system to continuously monitor the readout from the LPC and to recognize real events generated by particulates from noises using machine learning model. In this report, we will present how the data are prepared and how the model is trained. We will also discuss the performance of the model.
Paper: WEPS50
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS50
About: Received: 13 May 2024 — Revised: 22 May 2024 — Accepted: 22 May 2024 — Issue date: 01 Jul 2024
WEPS52
In situ plasma processing of superconducting cavities at JLab, 2024 update
2814
Jefferson Lab has an ongoing R&D program in plasma processing. The experimental program investigated processing using argon/oxygen and helium/oxygen gas mixtures. Plasma processing is a common technique where the free oxygen produced by the plasma breaks down and removes hydrocarbons from surfaces. This increases the work function and reduces the secondary emission coefficient. The initial focus of the effort was processing C100 cavities by injecting RF power into the HOM coupler ports. We also developed the methods for establishing a plasma in C75 cryomodules where the RF power is injected via the fundamental power-coupler. Four C100 cryomodules were in-situ processed in the CEBAF accelerator in May 2023 with the cryomodules returning to an operational status in Sept. 2023. The overall operational energy gain for the four cryomodules was 49 MeV. Methods, systems and results from processing cryomodules in the CEBAF accelerator and vertical test results will be presented. Current status and future plans will also be presented.
Paper: WEPS52
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS52
About: Received: 14 May 2024 — Revised: 22 May 2024 — Accepted: 22 May 2024 — Issue date: 01 Jul 2024
In the pursuit of next-generation SRF cavities with energetic condensation
The development of energetic condensation techniques has resulted in exceptional Nb film quality and improved Nb/Cu RF performance. Progress is continuously made in exploiting film forming and energetic processes to tailor the final film RF response. Convergence of parameters is emerging across techniques such as electron cyclotron resonance (ECR) and high power impulse magnetron sputtering (HiPIMS). The lessons learned also enable the development of NbTiN and Nb3Sn in single and multilayer structures. The resulting RF performance is studied with large quadrupole resonator samples and 1.3 GHz cavities at different temperatures, along with the cooldown effect and sensitivity to external applied magnetic fields. In conjunction, material and superconducting properties of the films and structures are evaluated with microscopy and magnetometry techniques to gain insight into various processes influence on the residual and flux induced surface resistances. This contribution presents the latest progress in exploiting processes involved in energetic condensation towards RF Q-slope mitigation for Nb/Cu films and the development of alternative superconductors and layered structures.
WEPS56
Design and prototyping of the Electron Ion Collider electron storage ring 591 MHz elliptical SRF cavity
2818
The electron storage ring (ESR) in the Electron Ion Collider (EIC) requires a challenging 591 MHz fundamental 17-cavity RF system to provide up to 10 MW CW power to the beam with up to 2.5 A beam current and a wide range of voltage. In this paper, we will report the latest RF and mechanical design status, as well as the prototyping and testing results.
Paper: WEPS56
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS56
About: Received: 18 May 2024 — Revised: 21 May 2024 — Accepted: 21 May 2024 — Issue date: 01 Jul 2024
WEPS57
Development of a plasma simulation tool for accelerating cavities
2822
Plasma processing of superconducting radio frequency (SRF) cavities has shown an improvement in accelerating gradient by reducing the radiation due to field emission and multipacting. Plasma processing is a common technique where the free oxygen produced by the plasma breaks down and removes hydrocarbons from surfaces. This increases the work function and reduces the secondary emission coefficient. The hydrocarbon fragments of H2, CO, CO2, and H2O are removed from the system with the process gas which is flowing through the system. Here, we present COMSOL for the first time to simulate the plasma processing of an SRF cavity. In this work, we use Jefferson Lab's C75 SRF cavities design as our case study. Using simulation, we predict the condition of plasma ignition inside the SRF cavity. The simulation provides information about the optimal rf coupling to the cavity, mode for plasma ignition, choice of gas concentration, power, and pressure.
Paper: WEPS57
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS57
About: Received: 15 May 2024 — Revised: 16 May 2024 — Accepted: 16 May 2024 — Issue date: 01 Jul 2024
WEPS58
Decoupling of nitrogen and oxygen impurities in nitrogen doped SRF cavities
2825
The performance of superconducting radiofrequency (SRF) cavities is critical to enabling the next generation of efficient, high-energy particle accelerators. Recent developments have focused on altering the surface impurity profile through in-situ baking, furnace baking, and doping to introduce and diffuse beneficial impurities such as nitrogen, oxygen, and carbon. However, the precise role and properties of each impurity are not well understood. In this work, we attempt to disentangle the role of oxygen and nitrogen impurities through time-of-flight secondary ion mass spectrometry of niobium samples baked at temperatures varying from 75-800°C with and without nitrogen injection. From these results, we developed treatments recipe that decouple the effects of oxygen and nitrogen in doping treatments. Understanding how these impurities and their underlying mechanisms drive further optimization in the tailoring of impurity profiles for high performing SRF cavities.
Paper: WEPS58
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS58
About: Received: 21 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS59
Microscopic understanding of the effects of impurities in low RRR SRF cavities
2829
The SRF community has shown that introducing certain impurities into high-purity niobium can improve quality factors and accelerating gradients. We question why some impurities improve RF performance while others hinder it. The purpose of this study is to characterize the impurities of niobium coupons with a low residual resistance ratio (RRR) and correlate these impurities with the RF performance of low RRR cavities so that the mechanism of impurity-based improvements can be better understood and improved upon. The combination of RF testing, temperature mapping, frequency vs temperature analysis, and materials studies reveals a microscopic picture of why low RRR cavities experience low BCS resistance behavior more prominently than their high RRR counterparts. We evaluate how differences in the mean free path, grain structure, and impurity profile affect RF performance. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.
Paper: WEPS59
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS59
About: Received: 22 May 2024 — Revised: 22 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
WEPS60
Preliminary design of a new superconducting harmonic cavity for HALF storage ring
2833
A superconducting (SC) 1.5 GHz (3rd harmonic) cavity is being developed for lengthening bunch and improving beam lifetime in the Hefei Advanced Light Facility (HALF) storage ring. This SC cavity is excited by an electron beam with 350 mA current, 1 nC charge, and ~6.7 ps length. This contribution presents optimizations on such a SC harmonic cavity in detail. Through optimizations it has a low R/Q < 45 Ω, which has potential to achieve a good bunch lengthening. It utilizes a large-radius beam pipe which traps the fundamental (1.5 GHz, TM010) mode, but allows all other cavity monopole and dipole higher-order-modes (HOMs) to travel into a room-temperature RF absorber. All of harmful HOMs are strong-ly damped using a pair of silicon carbide (SiC) rings. In addition, preliminary thermal analysis on the SiC rings is also described in this contribution
Paper: WEPS60
DOI: reference for this paper: 10.18429/JACoW-IPAC2024-WEPS60
About: Received: 15 May 2024 — Revised: 23 May 2024 — Accepted: 23 May 2024 — Issue date: 01 Jul 2024
Nb3Sn SRF cavities: from R&D to real accelerator – overview of recent developments
The superior superconducting properties of Nb3Sn promise enhanced RF performance (Q and Eacc) compared to Nb at any given temperature. The potential deployment of Nb3Sn-coated superconducting radiofrequency (SRF) cavities at 4 K, achieving performance comparable to Nb cavities at 2 K, signifies a transformative technology poised to enable innovative classes of SRF accelerators and improve the efficiency and cost-effectiveness of future accelerators. State-of-the-art Nb3Sn-coated single-cell Nb cavities have achieved accelerating gradients of ~20 MV/m with quality factors of ~1E10 at 4 K. Comparable performance has been demonstrated in cavities of different frequencies and multi-cell accelerator cavities currently in use. With these achievements, several ongoing projects are adopting Nb3Sn cavity technology to develop practical particle accelerators for industrial, environmental, and nuclear physics applications. This presentation provides an overview of recent developments in Nb3Sn cavity technology, transitioning from research and development to real-world accelerators while discussing the current challenges in the field.