TY - CONF AU - Miski-Oglu, M. AU - Aulenbacher, K. AU - Barth, W.A. AU - Basten, M. AU - Burandt, C. AU - Busch, M. AU - Conrad, T. AU - Dziuba, F.D. AU - Gettmann, V. AU - Heilmann, M. AU - Kürzeder, T. AU - Podlech, H. AU - Rubin, A. AU - Schnase, A. AU - Schwarz, M. AU - Yaramyshev, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Beam Commissioning of the Demonstrator Setup for the Superconducting Continuous Wave HIM/GSI-Linac J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - During successful beam commissioning of the superconducting 15-gap Crossbar H-mode cavity at GSI Helmholtzzentrum für Schwerionenforschung heavy ions up to the design beam energy have been accelerated. The design acceleration gain of 3.5 MeV inside a length of less than 70 cm has been reached with full transmission for heavy ion beams of up to 1.5 particle mueA. The measured beam parameters confirm sufficient beam quality. The machine beam commissioning is a major milestone of the R&D for the superconducting heavy ion continuous wave linear accelerator HELIAC of Helmholtz Institute Mainz (HIM) and GSI developed in collaboration with IAP Goethe-University Frankfurt. The next step is the procurement and commissioning of so called ’Advanced Demonstrator’ - the first of series cryo module for the entire accelerator HELIAC. Results of further Demonstrator beam tests, as well as the status of the Advanced demonstrator project will be reported. PB - JACoW Publishing CP - Geneva, Switzerland SP - 33 EP - 36 KW - cavity KW - linac KW - heavy-ion KW - cryomodule KW - solenoid DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOZZPLM1 UR - http://jacow.org/ipac2019/papers/mozzplm1.pdf ER - TY - CONF AU - Litvinov, S.A. AU - Steck, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Achromatic Isochronous Mode of the ESR at GSI J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The isochronous optics of the ESR is a unique ion-optical setting in which the ring is operated as a Time-of-Flight Mass-Spectrometer and is used for direct mass measurements of short-lived exotic nuclei. The present isochronous optics had been performed only making a negative dispersion in the straight sections of the ESR of about -7 m. This negative dispersion makes the injection into the ESR very complicated and strict the transmission of the ions in the ring. Moreover, the non-achromatism of the ESR brings a supplementary uncorrectable first-order transverse contribution to the revolution time. In order to make the ESR achromatic, to improve injection and the isochronicity a new achromatic isochronous optics has been calculated and will be presented here in details. PB - JACoW Publishing CP - Geneva, Switzerland SP - 124 EP - 126 KW - optics KW - sextupole KW - experiment KW - detector KW - emittance DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPGW022 UR - http://jacow.org/ipac2019/papers/mopgw022.pdf ER - TY - CONF AU - Sapinski, M. AU - Geithner, O. AU - Heßler, C. AU - Reimann, S. AU - Schütt, P. AU - Vossberg, M. AU - Walasek-Höhne, B. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Measurements of the GSI Transfer Beam Lines Ion Optics J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - GSI High Energy Beam Transfer lines (HEST) link the SIS18 synchrotron with two storage rings (Experimental Storage Ring and Cryring) and six experimental caves. The recent upgrades to HEST beam instrumentation enables precise measurements of beam properties along the lines and allow for faster and more precise beams setup on targets. Preliminary results of some of the measurements performed during runs in 2018 and 2019 are presented here. The focus is on response matrix measurements and quadrupole scans performed on HADES beam line. The errors and future improvements are discussed. PB - JACoW Publishing CP - Geneva, Switzerland SP - 131 EP - 134 KW - quadrupole KW - extraction KW - experiment KW - emittance KW - storage-ring DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPGW024 UR - http://jacow.org/ipac2019/papers/mopgw024.pdf ER - TY - CONF AU - Vilsmeier, D.M. AU - Bai, M. AU - Sapinski, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Transfer Line Optics Design Using Machine Learning Techniques J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Optimization of transfer line optics is essential for delivering high quality beams to the experimental areas. This type of optimization is usually done by hand and relies on the experience of operators. The nature of this task is repetitive though highly complex. Besides optimizing the beam quality at the experiments this task is often accompanied by secondary objectives or requirements such as keeping the beam losses below an acceptable threshold. In the past years Deep Learning algorithms have experienced a rapid development and gave rise to various advanced software implementations which allow for straightforward usage of corresponding techniques, such as automatic differentiation and gradient backpropagation. We investigate the applicability and performance of these techniques in the field of transfer line optics optimization, specifically for the HADES beamline at GSI, in form of gradient-based differentiable simulators. We test our setup on results obtained from MADX simulations and compare our findings to different gradient-free optimization methods. Successfully employing such methods relieves operators from the tedious optimization tasks. PB - JACoW Publishing CP - Geneva, Switzerland SP - 139 EP - 142 KW - target KW - simulation KW - quadrupole KW - optics KW - operation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPGW026 UR - http://jacow.org/ipac2019/papers/mopgw026.pdf ER - TY - CONF AU - Dutheil, Y. AU - Alden, S.E. AU - Alemany-Fernández, R. AU - Apyan, A. AU - Bartosik, H. AU - Bessonov, E.G. AU - Biancacci, N. AU - Bosco, A. AU - Bruce, R. AU - Castelli, F. AU - Curatolo, C. AU - Czodrowski, P. AU - Fedosseev, V. AU - Gibson, S.M. AU - Goddard, B. AU - Hirlaender, S. AU - Jowett, J.M. AU - Kersevan, R. AU - Kowalska, M. AU - Kroeger, K. AU - Lamont, M. AU - Manglunki, D. AU - Martens, A. AU - Molson, J. AU - Nevay, L.J. AU - Petrenko, A.V. AU - Petrillo, V. AU - Sapinski, M. AU - Schaumann, M. AU - Serafini, L. AU - Stöhlker, T. AU - Weber, G. AU - Wu, Y.K. AU - Zimmermann, F. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Gamma Factory at CERN: Design of a Proof-of-Principle Experiment J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The Gamma Factory (GF) initiative proposes to create novel research tools at CERN by producing, accelerating and storing highly relativistic partially stripped ion beams in the LHC rings and by exciting their atomic degrees of freedom by lasers, to produce high-energy photon beams. Their intensity would be several orders of magnitude higher than those of the presently operating light sources in the particularly interesting gamma-ray energy domain reaching up to 400 MeV. In this energy domain, the high-intensity photon beams can be used to produce secondary beams of polarized electrons, polarized positrons, polarized muons, neutrinos, neutrons and radioactive ions. Over the years 2017-2018 we have demonstrated that these partially stripped ion beams can be successfully produced, accelerated and stored in the CERN accelerator complex, including the LHC. The next step of the project is to build a proof of principle experiment in the SPS to validate the principal GF concepts. This contribution will present the initial conceptual design of this experiment along with its main challenge - the demonstration of the fast cooling method of partially stripped ion beams. PB - JACoW Publishing CP - Geneva, Switzerland SP - 685 EP - 688 KW - photon KW - laser KW - experiment KW - electron KW - cavity DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPRB052 UR - http://jacow.org/ipac2019/papers/moprb052.pdf ER - TY - CONF AU - Heilmann, M. AU - Du, X. AU - Groening, L. AU - Mickat, S. AU - Mühle, C. AU - Rubin, A. AU - Srinivasan, V. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - FoS Cavity of the Alvarez 2.0 DTL as FAIR Injector J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The Alvarez 2.0 DTL will be the new post-stripper DTL of the UNILAC at GSI. The existing GSI with its LINAC and SIS18 comprise the main operation injector chain for the Facility for Antiproton and Ion Research FAIR. The new Alvarez-DTL has an operation frequency of 10⁸.4 MHz, an input energy of 1.358 MeV/u and the output energy is 11.4 MeV/u with a total length of 55 m. The presented FoS section will be part of the first cavity of the Alvarez 2.0 DTL. The FoS-cavity with 11 drift tubes (including quadrupole singlets) and a total length of 1.9 m will be copper plated in GSI for high power tests. The design of the quadrupole singlet magnet is finalized; a prototype of a fully functional magnet with drift tube and stems will be fabricated within a design study. Empty drift tubes and all components of the tank shall be delivered 2019 for first low level RF investigations. PB - JACoW Publishing CP - Geneva, Switzerland SP - 871 EP - 874 KW - DTL KW - cavity KW - quadrupole KW - operation KW - linac DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS015 UR - http://jacow.org/ipac2019/papers/mopts015.pdf ER - TY - CONF AU - Du, X. AU - Groening, L. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Compression and Noise Reduction of Field Maps J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Errors from discretization and large data volume of field maps is a concern for beam dynamics simulations with respect to achievable accuracy and to the required amount of time. High-order singular value decomposition (HOSVD) has recently emerged as simple, effective, and adaptive tool to extract the essentials from multidimensional data. This paper is on the feasibility of compression and noise reduction of electromagnetic field map data with HOSVD. The method has been applied to an electric field map of a DTL cavity with 11 m in length comprising 55 rf-gaps. The original field map data of 220 MB was converted into practically noise-free data of just 20 KB. Noise was reduced by 95% as demonstrated using a cubic cavity for which the analytical field map is available. PB - JACoW Publishing CP - Geneva, Switzerland SP - 875 EP - 877 KW - cavity KW - DTL KW - simulation KW - MMI KW - extraction DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS016 UR - http://jacow.org/ipac2019/papers/mopts016.pdf ER - TY - CONF AU - Hähnel, H. AU - Kleffner, C.M. AU - Ratzinger, U. AU - Syha, M. AU - Tiede, R. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - End to End Simulations and Error Studies of the FAIR Proton Linac J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The FAIR proton linac is developed as the high current proton injector for the future FAIR antiproton production chain at GSI. It will provide a 70 mA proton beam at an energy of 68 MeV to the SIS18 synchrotron. The linac consists of an ECR ion source, followed by a ladder RFQ and a normalconducting linac based on CH-type cavities. High beam currents and strict beam quality requirements were the main drivers for the beam dynamics design. To ensure matching between the individual sections and validate the injector design as a whole, end to end simulations were performed using TraceWin with 3D fieldmaps of the CH-linac. In this paper, the final cavity design, as well as the results of end to end simulations and error studies are discussed. PB - JACoW Publishing CP - Geneva, Switzerland SP - 885 EP - 888 KW - linac KW - simulation KW - cavity KW - rfq KW - proton DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS019 UR - http://jacow.org/ipac2019/papers/mopts019.pdf ER - TY - CONF AU - Kleffner, C.M. AU - Appel, S. AU - Berezov, R. AU - Fils, J. AU - Forck, P. AU - Gerhard, P. AU - Hähnel, H. AU - Kaiser, M. AU - Knie, K. AU - Krämer, A. AU - Mühle, C. AU - Puetz, S. AU - Ratzinger, U. AU - Schnase, A. AU - Schreiber, G. AU - Schuett, M. AU - Seibel, A. AU - Sieber, T. AU - Srinivasan, V. AU - Syha, M. AU - Trüller, J. AU - Vinzenz, W. AU - Vossberg, M. AU - Will, C. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Status of the FAIR Proton LINAC J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - For the production of Antiproton beams with sufficient intensities, a dedicated high-intensity 325 MHz Proton linac is currently under construction. The Proton linac shall deliver a beam current of up to 70 mA with an energy of 68 MeV for injection into SIS18. The source is designed for the generation of 100 mA beams. The Low-Energy Beam Transport line (LEBT) contains two magnetic solenoid lenses enclosing a diagnostics chamber, a beam chopper and a beam conus. A ladder 4-Rod RFQ and six normal conducting crossbar cavities of CCH and CH type arranged in two sections accelerate the beam to the final energy of 68 MeV. The technical design of the DTL CH cavities are presented and the commissioning measurements of the ion source are described. The construction and the procurement progress, the design and testing results of the key hardware are presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 889 EP - 891 KW - proton KW - linac KW - cavity KW - rfq KW - simulation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS020 UR - http://jacow.org/ipac2019/papers/mopts020.pdf ER - TY - CONF AU - Lauber, S. AU - Aulenbacher, K. AU - Barth, W.A. AU - Burandt, C. AU - Dziuba, F.D. AU - Forck, P. AU - Gettmann, V. AU - Heilmann, M. AU - Kürzeder, T. AU - List, J. AU - Miski-Oglu, M. AU - Podlech, H. AU - Rubin, A. AU - Schwarz, M. AU - Sieber, T. AU - Yaramyshev, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Reconstruction of the Longitudinal Phase Portrait for the SC CW Heavy Ion HELIAC at GSI J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - At the GSI Helmholtzzentrum für Schwerionenforschung (GSI) in Darmstadt, Germany, the HElmholtz LInear ACcelerator (HELIAC) is currently under construction. The HELIAC comprises superconducting multigap Crossbar H-mode (SC CH) cavities. The input beam is delivered by an already existing High Charge Injector (HLI). For the further development of the accelerator a detailed knowledge of the input beam parameters to the SC section is necessary. A method for beam reconstruction is incorporated, which provides for longitudinal beam characteristics using measurements with a beam shape monitor and a particle simulation code. This finalizes the investigations on 6D beam parameters, following previous measurements in transversal phase space. The reconstruction of the longitudinal phase portrait is presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 898 EP - 901 KW - heavy-ion KW - linac KW - cavity KW - proton KW - quadrupole DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS024 UR - http://jacow.org/ipac2019/papers/mopts024.pdf ER - TY - CONF AU - Podlech, H. AU - Baggemann, J. AU - Brückel, Th. AU - Böhm, S. AU - Cronert, T. AU - Doege, P.-E. AU - Droba, M. AU - Gutberlet, T. AU - Kümpel, K. AU - Lamprecht, S. AU - Li, J. AU - Mauerhofer, E. AU - Meusel, O. AU - Petry, N.F. AU - Rücker, U. AU - Schneider, P.P. AU - Schwarz, M. AU - Zakalek, P. AU - Zhang, C. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Conceptual Design of the Proton LINAC for the High Brilliance Neutron Source HBS J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Due to the decommissioning of several research reactors there will be a severe drop in available neutrons for research in Europe in the next decade despite the commissioning of the European Spallation Source (ESS). Compact accelerator-based neutron sources (CANS) could close this gap. The High Brilliance Neutron Source (HBS) currently under development at Forschungszentrum Jülich is scalable in terms of beam energy and power due to its modular design. The driver Linac for HBS at will accelerate a 100 mA proton beam to 70 MeV. The Linac is operated with a beam duty cycle of up to 6% (11% RF duty cycle) and can simultaneously deliver three proton pulse lengths (384 Hz@52 mu-s, 96 Hz@208 mu-s and 24 Hz@832 mu-s) for three neutron production targets. In order to minimize the development effort and the technological risk, state-of-the-art technology of the MYRRHA injector is used. The front end of the HBS Linac consists of an ECR source, LEBT and a 2.5 MeV RFQ followed by a CH-DTL with 35 room temperature CH-cavities. All RF structures are operated at 176.1 MHz and are designed for high duty cycle. Solid-state amplifiers up to 500 kW are used as RF drivers. Due to the beam current and the high average beam power of up to 420 kW, particular attention is paid to beam dynamics. In order to minimize losses, a quasi-periodic lattice with constant negative phase is used. The contribution describes the conceptual design and the challenges of such a modern high power proton accelerator with high reliability and availability. PB - JACoW Publishing CP - Geneva, Switzerland SP - 910 EP - 913 KW - linac KW - rfq KW - cavity KW - neutron KW - proton DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS027 UR - http://jacow.org/ipac2019/papers/mopts027.pdf ER - TY - CONF AU - Schwarz, M. AU - Aulenbacher, K. AU - Barth, W.A. AU - Basten, M. AU - Burandt, C. AU - Busch, M. AU - Conrad, T. AU - Dziuba, F.D. AU - Gettmann, V. AU - Heilmann, M. AU - Kürzeder, T. AU - Lauber, S. AU - List, J. AU - Miski-Oglu, M. AU - Podlech, H. AU - Rubin, A. AU - Yaramyshev, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Advanced Beam Dynamics Design for the Superconducting Heavy Ion Accelerator HELIAC J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The standalone superconducting (SC) continuous wave (CW) heavy ion linac HELIAC (HElmholtz LInear ACcelerator) is a common project of GSI and HIM under key support of IAP Frankfurt and in collaboration with Moscow Engineering Physics Institute (MEPhI) and Moscow Institute for Theoretical and Experimental Physics (KI-ITEP). It is intended for future experiments with heavy ions near the Coulomb barrier within super-heavy element (SHE) research and aims at developing a linac with multiple CH cavities as key components downstream the High Charge State Injector (HLI) at GSI. The design is challenging due to the requirement of intense beams in CW mode up to a mass-to-charge ratio of 6, while covering a broad output energy range from 3.5 to 7.3 MeV/u with minimum energy spread. In 2017 the first superconducting section of the linac has been successfully commissioned and extensively tested with beam at GSI. In the light of experience gained in this research so far, the beam dynamics layout for the entire linac has recently been updated and optimized with particular emphasis on realistic assumptions of cavity gap and drift lengths as well as gap voltage distributions for CH3’CH11. PB - JACoW Publishing CP - Geneva, Switzerland SP - 928 EP - 931 KW - cavity KW - linac KW - heavy-ion KW - SRF KW - acceleration DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS034 UR - http://jacow.org/ipac2019/papers/mopts034.pdf ER - TY - CONF AU - Ondreka, D. AU - Dimopoulou, C. AU - Hüther, H.C. AU - Liebermann, H. AU - Stadlmann, J. AU - Steinhagen, R.J. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Recommissioning of SIS18 After FAIR Upgrades J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The synchrotron SIS18 of the GSI facility has recently resumed beam operation after a long shutdown, during which major upgrades for the operation of SIS18 in the FAIR facility were realized. This signifies a major milestone for the mission of GSI and FAIR. On one hand, the scientific program of GSI depends strongly on beam from SIS18, including the very important developments of detectors for FAIR experiments. On the other hand, large parts of the existing GSI accelerator facility, including SIS18, are now operated with the FAIR control system, demonstrating its suitability for control of a large scale accelerator facility. Commissioning of the new control system started during the shutdown with a series of dry runs, which proved very useful to establish the basic functionalities. Recommissioning of SIS18 was further facilitated by the fact that the machine model of SIS18, implemented in the modeling framework LSA, had already been tested with beam several years before the shutdown. Thus, all operation modes of SIS18, including multi-turn injection, electron cooling, as well as fast and slow extraction could be successfully commissioned during the first weeks of operation. Other commissioning activities concerned the operation of new devices installed during the shutdown. These devices, mostly installed to prepare SIS18 for the operation with FAIR design parameters, open new possibilities in the standard operation of SIS18. A challenge for the operation of SIS18 is posed by ground motion due to ground water lowering for the nearby FAIR construction site. Surveys revealed that SIS18 subsided by several centimeters during one year. Even though the machine was realigned prior to recommissioning, the dynamics of the ground motion will continue to affect operation of SIS18. PB - JACoW Publishing CP - Geneva, Switzerland SP - 932 EP - 935 KW - MMI KW - operation KW - controls KW - extraction KW - cavity DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS035 UR - http://jacow.org/ipac2019/papers/mopts035.pdf ER - TY - CONF AU - Vossberg, M. AU - Bencini, V. AU - Garland, J.M. AU - Gerhard, P. AU - Groening, L. AU - Lallement, J.-B. AU - Lombardi, A.M. AU - Mickat, S. AU - Vormann, H. AU - Xiao, C. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - RFQ Electrodes Change and Upgrade Option at the UNILAC HSI Injector J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - In order to meet the beam intensity and quality requirements imposed by FAIR, the HSI-RFQ beam dynamics originally dating from 2009 has been re-designed recently at CERN. Front-to-end simulations demonstrated that the new design meets the FAIR targets. Implementation of the new electrodes, initially planned for 2019, will require re-adaption of the RFQ cavity rf-parameters by re-shaping the stems that keep the electrodes. However, during the beam time 2018 the existing RFQ did not reach its nominal voltage most likely due to expired lifetime of the electrodes originating from 2009. In order to shorten the RFQ maintenance period and to minimize any risk for upcoming beam time 2019, it was decided to post-pone the implementation of the new design and rather just re-producing the 2009 design electrodes. This contribution is on the re-production process as short-term solution and on the full implementation of the new design as mid-term solution. CST simulations performed at GSI assure that the resonance frequency with the new electrode geometry is recuperated through corrections of the carrier rings. The status of the exchange of the electrodes and simulations for the adaptation of the new electrode design are presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 936 EP - 939 KW - rfq KW - simulation KW - operation KW - cavity KW - MMI DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS036 UR - http://jacow.org/ipac2019/papers/mopts036.pdf ER - TY - CONF AU - Seibel, A. AU - Kleffner, C.M. AU - Knie, K. AU - Ratzinger, U. AU - Vossberg, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Comparison Between Measurement and Simulation of a Full Scale Prototype for the Proton Injector at FAIR J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - A dedicated 68 MeV, 70 mA proton injector is required for the research program at FAIR (Facility for Antiproton and Ion Research). This 325 MHz linear injector contains a RFQ and six CH structures. The CH (Crossbar H-mode) structures are working in the H₂10 mode. The main acceleration of this room temperature linac will be provided by the CH structures. For the second acceleration from 11.5 MeV to 24.2 MeV a full scale prototype has been built. This structure consists of two individual CH resonators and a coupling cell. Inside the structure there are 17 tuners, they have an impact on the electric field and the frequency. For operation a flat field is required, therefore this tuners must be correctly positioned. Some series of low level tuning and frequency measurements were done to determine the size of the tuners. Low level measurements and simulations will be compared and presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 940 EP - 942 KW - cavity KW - simulation KW - proton KW - linac KW - resonance DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-MOPTS037 UR - http://jacow.org/ipac2019/papers/mopts037.pdf ER - TY - CONF AU - Bozyk, L.H.J. AU - Aumüller, S. AU - Spiller, P.J. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Investigations on Cryopanels in the Room Temperature Heavy Ion Synchrotron SIS18 J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The heavy ion synchrotron SIS18 at GSI will serve as injector ring for the FAIR-facility and provide high intensity heavy ion beams. The operation of such beams requires the usage of low charge states, which have high cross sections for ionization. To overcome this issue, many upgrade measure have been realized in the past decade, such as the installation of an ion catcher system with low desorption surfaces and coating 65% of the circumference of SIS18 with NEG to lower the static gas pressure. Since the vacuum dynamics during operation prevent the achievement of the intensity goals for FAIR, new concepts have to be developed, to increase the beam intensity. One idea is the installation of additional pumping speed in the form of cryogenic surfaces. Heavy residual gas components, which have the highest ionization cross sections can be cryopumped at moderate temperatures, i.e. already at 50-80 K. In fact, the only typical residual gas component which can not be pumped via cryosorption in this temperature regime is Hydrogen, which has a factor 50 lower ionization cross sections than Argon, the heaviest residual gas component. In this paper, we present a study of the integration of cryopanels into the vacuum chambers of SIS18. PB - JACoW Publishing CP - Geneva, Switzerland SP - 1372 EP - 1374 KW - vacuum KW - cryogenics KW - heavy-ion KW - synchrotron KW - operation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-TUPMP054 UR - http://jacow.org/ipac2019/papers/tupmp054.pdf ER - TY - CONF AU - Friederich, S. AU - Aulenbacher, K. AU - Matejcek, C. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Vacuum Lifetime and Surface Charge Limit Investigations Concerning High Intensity Spin-polarized Photoinjectors J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The Small Thermalized Electron Source at Mainz (STEAM) is a dc photoemission source. It is designed to operate at up to 200kV bias voltage with an accelerating field of up to 5 MV/m at the cathode surface. In several experiments, the properties of GaAs operating under the conditions of spin-polarized photoemission were investigated. Its performance, quantum efficiency lifetime and surface charge limit observations for bulk-GaAs will be discussed. PB - JACoW Publishing CP - Geneva, Switzerland SP - 1954 EP - 1957 KW - cathode KW - electron KW - vacuum KW - laser KW - experiment DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-TUPTS011 UR - http://jacow.org/ipac2019/papers/tupts011.pdf ER - TY - CONF AU - Appel, S. AU - Reimann, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Beam Line Optimization Using Derivative-Free Algorithms J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The present study focuses on the beam line optimization from the heavy-ion synchrotron SIS18 to the HADES experiment. BOBYQA (Bound Optimization BY Quadratic Approximation) solves bound constrained optimization problems without using derivatives of the objective function. The Bayesian optimization is an other strategy for global optimization of costly, noisy functions without using derivatives. A python programming interface to MADX allow the use of the python implementation of BOBYQA and Bayesian method. This gave the possibility to use tracking simulation with MADX to determine the loss budget for each lattice setting during the optimization and compare both optimization methods. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2307 EP - 2310 KW - experiment KW - target KW - heavy-ion KW - site KW - interface DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPMP005 UR - http://jacow.org/ipac2019/papers/wepmp005.pdf ER - TY - CONF AU - Rost, A. AU - Adamczewski-Musch, J. AU - Galatyuk, T. AU - Linev, S. AU - Pietraszko, J. AU - Sapinski, M. AU - Traxler, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Performance of the CVD Diamond Based Beam Quality Monitoring System in the HADES Experiment at GSI* J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The beam quality monitoring of extracted beams from SIS18 at GSI, transported to the HADES experiment is of great importance to ensure a high efficient data recording. The main detector system used for this purpose is the Start-Veto system which consists of two diamond based sensors made of pcCVD and scCVD diamond materials. Both sensors are equipped with a double-sided strip segmented metallization (300 µm width) which allows a position determination of the beam. Those sensors are able to deliver a time precision <100 ps and can handle rate capabilities up to 10⁷ particles/s/channel. Beside the diamond sensors a plastic scintillation based beam halo detector is used. The read-out of the detectors is based on the TRB3 system*. A 264 channel TDC (Time to Digital Converter) is implemented in FPGA technology with 10 ps precision. The TRB3 system serves as a fast and flexible Data Acquisition System (DAQ) with integrated scaler capability. The analysis and online visualization is performed using the Data Acquisition Backbone Core (DABC)** framework. In this contribution the performance of the system, which was used in order to evaluate an Ar and Ag ion beam delivered by the SIS 18 accelerator, will be discussed. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2507 EP - 2509 KW - monitoring KW - detector KW - experiment KW - extraction KW - target DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPGW019 UR - http://jacow.org/ipac2019/papers/wepgw019.pdf ER - TY - CONF AU - Sieber, T. AU - De Gersem, H. AU - Golm, J. AU - Haider, D.M. AU - Marsic, N. AU - Müller, W.F.O. AU - Reeg, H. AU - Schmelz, M. AU - Schmidl, F. AU - Schwickert, M. AU - Seidel, P. AU - Stolz, R. AU - Stöhlker, T. AU - Tan, J. AU - Tranquille, G. AU - Tympel, V. AU - Zakosarenko, V. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Next Generation Cryogenic Current Comparator (CCC) for nA Intensity Measurement J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - A Cryogenic Current Comparator (CCC) is an extremely sensitive DC-Beam Transformer based on superconducting SQUID technology. Recently, a CCC without a toroidal core and with an axially oriented magnetic shielding has been developed at the Institute of Photonic Technologies (IPHT) Jena/Germany. It represents a compact and lightweight alternative to the ’classical’ CCC, which was originally developed at PTB Braunschweig and is successfully in operation in accelerators at GSI and CERN. Excellent low-frequency noise performance was demonstrated with a prototype of this new CCC-type. Current measurements and further tests are ongoing, first results are presented together with simulation calculations for the magnetic shielding. The construction from lead as well as simplified manufacturing results in drastically reduced costs compared to formerly used Nb-CCCs. Reduced weight also puts less constraints on the cryostat. Based on highly sensitive SQUIDs, the new prototype device shows a current sensitivity of about 6 pA/Hz1/2 in the white noise region. The measured and calculated shielding factor is ~135 dB. These values, together with a significant cost reduction - resulting also from a compact cryostat design - opens up the way for widespread use of CCCs in modern accelerator facilities. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2510 EP - 2513 KW - shielding KW - cryogenics KW - pick-up KW - coupling KW - detector DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPGW020 UR - http://jacow.org/ipac2019/papers/wepgw020.pdf ER - TY - CONF AU - Steinhagen, R.J. AU - Bär, R. AU - Franke, A. AU - Krimm, A. AU - Lüghausen, K. AU - Ondreka, D. AU - Schwinn, A. AU - Thieme, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Generic Digitization of Analog Signals at FAIR – First Prototype Results at GSI J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - FAIR operation and notably the new FAIR Control Centre will be based on a ’fully-digital’ control paradigm for which about 300 generic digitizers covering analog bandwidths and sampling frequencies from a few MHz to a GHz will be deployed. The aim is to acquire all pertinent accelerator system and beam parameters to facilitate a multi-mission of continuous performance tracking, (semi-)automated feedbacks and setup tools, early detection and isolation of hardware failures or near-misses, and to provide a dependable generic platform for equipment experts that enable post-mortem analyses or remote diagnostics. The goal of the controls integration was to provide a generic abstraction of the vendor-specific electro-mechanical form-factor and software interfaces based on modern software-defined-radio (SDR) principles. In addition to a ns-level-syncronised time- and frequency-domain based acquisitions, the interface provides a wide range of generic user-configurable signal post-processing routines common for SDRs and also found in many modern benchtop oscilloscopes, spectrum- or vector-network analysers. The acquired raw and derived signals are exported to the FAIR control system using a standardised front-end software architecture (FESA) and a common middle-ware (CMW). Further integration goals were to simplify possible future extensions, compactness, readability, reusability, testability, and long-term maintainability of the code-based which led to the re-use of established open-source signal processing and data fitting frameworks such as GNU-Radio and ROOT. While explicitly kept open for new or other specific digitizer or SDRs, the initial integration, prototyping, and testing have been done for the PS3000-, PS4000-, and PS600-series of digitizers from Pico Technology. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2514 EP - 2517 KW - controls KW - interface KW - software KW - hardware KW - operation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPGW021 UR - http://jacow.org/ipac2019/papers/wepgw021.pdf ER - TY - CONF AU - Salehilashkajani, A. AU - Ady, M. AU - Chritin, N. AU - Forck, P. AU - Glutting, J. AU - Jones, O.R. AU - Kersevan, R. AU - Marriott-Dodington, T. AU - Mazzoni, S. AU - Rossi, A. AU - Schneider, G. AU - Udrea, S. AU - Veness, R. AU - Welsch, C.P. AU - Zhang, H.D. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Commissioning of the Prototype for a New Gas Curtain Beam Profile Monitor Using Beam Induced Fluorescence for HL-LHC J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - A new supersonic gas-jet curtain based beam profile monitor is under development for minimally invasive simultaneous transverse profile diagnostics of proton and electron beams, at pressures compatible with LHC. The monitor makes use of a thin gas-jet curtain angled at 45 degrees with respect to the charged particle beams. The fluorescence caused by the interaction between the curtain and the beam can then be detected using a dedicated imaging system to determine its transverse profile. This contribution details design features of the monitor, discusses the gas-jet curtain formation and presents various experimental tests, including profile measurements of an electron beam using nitrogen and neon curtains. The gas-jet density was estimated by correlating it with the number of photons detected by the camera. These measurements are then compared with results obtained using a movable pressure gauge. This monitor has been commissioned in collaboration with CERN, GSI and the University of Liverpool. It serves as a first prototype of a final design that will be placed in the LHC beam line to measure the profile of the proton beam. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2709 EP - 2712 KW - electron KW - photon KW - gun KW - background KW - experiment DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPGW093 UR - http://jacow.org/ipac2019/papers/wepgw093.pdf ER - TY - CONF AU - Zhang, H.D. AU - Ady, M. AU - Forck, P. AU - Glutting, J. AU - Jones, O.R. AU - Marriott-Dodington, T. AU - Mazzoni, S. AU - Rossi, A. AU - Salehilashkajani, A. AU - Schneider, G. AU - Udrea, S. AU - Veness, R. AU - Welsch, C.P. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Development of Supersonic Gas-Sheet-Based Beam Profile Monitors J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Non-destructive beam profile monitoring is very desirable, essentially for any particle accelerator but particularly for high-energy and high-intensity machines. Supersonic gas jet-based monitors, detecting either the ionization or fluorescence of a gas sheet interacting with the primary beam to be characterized, allow for minimally invasive measurements. They can also be used over a wide energy range, from keV to TeV beams. This contribution gives an overview of the jet-based ionization and fluorescence beam profile monitors which have been developed, built and tested at the Cockcroft Institute. It discusses gas sheet generation, vacuum considerations, choice of gas species and detection methods. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2717 EP - 2720 KW - electron KW - photon KW - background KW - radiation KW - monitoring DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPGW096 UR - http://jacow.org/ipac2019/papers/wepgw096.pdf ER - TY - CONF AU - Busch, M. AU - Barth, W.A. AU - Basten, M. AU - Conrad, T. AU - Dziuba, F.D. AU - Miski-Oglu, M. AU - Müller, P. AU - Podlech, H. AU - Schwarz, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Overview on SC CH-Cavity Development J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - During the last decades an enermous effort has been put into the development of low beta structures for hadron acceleration worldwide. Since hadrons exhibit a very inert velocity gain due to their high mass this change in speed has to be taken into account when utilizing low beta cavities. At the Institute of Applied Physics (IAP), Frankfurt, Germany, five multi-cell CH-cavities (Crossbar H-Mode) have been developed and tested for different kind of applications so far. In addition to the successfully tested original 360 MHz prototype further structures envisaged for beam operation have been fabricated and tested. Overview, status and outlook of this cavity technology is topic of this contribution. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2822 EP - 2825 KW - cavity KW - linac KW - SRF KW - heavy-ion KW - status DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPRB012 UR - http://jacow.org/ipac2019/papers/weprb012.pdf ER - TY - CONF AU - Dziuba, F.D. AU - Aulenbacher, K. AU - Barth, W.A. AU - Basten, M. AU - Burandt, C. AU - Busch, M. AU - Conrad, T. AU - Gettmann, V. AU - Heilmann, M. AU - Kürzeder, T. AU - Lauber, S. AU - List, J. AU - Miski-Oglu, M. AU - Podlech, H. AU - Salvatore, J. AU - Schnase, A. AU - Schwarz, M. AU - Yaramyshev, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Further RF Measurements on the Superconducting 217 MHz CH Demonstrator Cavity for a CW Linac at GSI J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Recently, the first section of the superconducting (sc) continuous wave (cw) Linac has been extensively tested with heavy ion beam from the GSI High Charge State Injector (HLI). During this testing phase, the reliable operability of 217 MHz multi gap crossbar-H-mode (CH) cavities has been successfully demonstrated. The sc 217 MHz CH cavity (CH⁰) of the demonstrator setup accelerated heavy ions up to the design beam energy and even beyond at high beam intensities and full transmission. This worldwide first beam test with a sc CH cavity is a major milestone on the way realizing the entire sc cw Linac project. In this contribution further RF measurements on the cavity are presented providing full characterization of the RF structure. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2826 EP - 2829 KW - cavity KW - linac KW - heavy-ion KW - MMI KW - operation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPRB014 UR - http://jacow.org/ipac2019/papers/weprb014.pdf ER - TY - CONF AU - Kürzeder, T. AU - Aulenbacher, K. AU - Barth, W.A. AU - Burandt, C. AU - Conrad, J. AU - Dziuba, F.D. AU - Gettmann, V. AU - Heine, R.G. AU - Hug, F. AU - Lauber, S. AU - List, J. AU - Miski-Oglu, M. AU - Stengler, T. AU - Yaramyshev, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Cleanroom Installations for SRF Cavities at the Helmholtz-Institut Mainz J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - At the Helmholtz-Institut Mainz (HIM) a cleanroom has been equipped with new tools and installations for the planned treatment of different superconducting RF-cavities. At first TESLA/XFEL type 9-cell cavities for the Mainz Energy-Recovering Superconducting Accelerator (MESA) project or 217 MHz multigap Crossbar H-mode cavities for the HElmholtz LInear ACcelerator (HELIAC) under development by HIM and GSI will be treated. The cleanroom installations, including the greyroom, cover an area of about 155 sqm. In its ISO-class 6 area a large ultrasonic and a conductance rinsing bath has been installed recently. A high pressure rinsing cabinet (HPR) has been implemented between the ISO-class 6 and 4 cleanroom. A RF-cavity can be loaded and unloaded from both sides. HPR treatments are possible for cavities of up to 1.4 m length and about 0.7 m diameter. For drying the ISO-class 4 clean room is equipped with a 160 C vacuum oven. New cleanroom lifters allow the handling of up to 200 kg heavy objects. A rail system in the cleanroom floor is installed to move out the entire cold string of the cleanroom after assembly and leak testing. First operational experiences with this facility will be presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 2830 EP - 2833 KW - cavity KW - operation KW - vacuum KW - heavy-ion KW - SRF DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPRB015 UR - http://jacow.org/ipac2019/papers/weprb015.pdf ER - TY - CONF AU - Franchetti, G. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Coherent vs Incoherent Effects and Debye Length J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - In this proceeding it is discussed the effect of coherent vs. incoherent effect and discussing the validity of frozen models of space charge according to the Debye length and beam radius. This in view of discussing the relation of IBS and space charge PB - JACoW Publishing CP - Geneva, Switzerland SP - 3116 EP - 3118 KW - space-charge KW - plasma KW - focusing KW - lattice KW - vacuum DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPTS014 UR - http://jacow.org/ipac2019/papers/wepts014.pdf ER - TY - CONF AU - Dastan, S. AU - Livinov, S. AU - Rahighi, J. AU - Saffari, R. AU - Steck, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - The ESR Closed Orbit Calculation and Simulation J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The commissioning of the ESR with a new control system based on the LSA (LHC System Architecture) has started recently. This new control system is under development and considers all aspects of the expected functionality to operate the GSI/FAIR accelerators and incorporates the present GSI controls infrastructure*. Two years ago, the old control system which was based on outdated computers and operating system, was discontinued. So, both the heavy ion synchrotron SIS-18 and the Experimental Storage Ring (ESR) operation from now on have to be performed with the new FAIR control system. In order to introduce an improved model to the control system change, new calculations and simulations for SIS and ESR are necessary. In this paper we summarize the results of closed orbit calculations for the ESR which are done with three different codes, namely: ELEGANT*, MAD-X and MIRKO. Also, because the results of ELEGANT and MAD-X in this issue are similar to each other, we present ELEGANT results in the report. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3349 EP - 3351 KW - controls KW - simulation KW - electron KW - experiment KW - MMI DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-WEPTS100 UR - http://jacow.org/ipac2019/papers/wepts100.pdf ER - TY - CONF AU - Golm, J. AU - De Gersem, H. AU - Fernandes, M.F. AU - Haider, D.M. AU - Kurian, F. AU - Marsic, N. AU - Müller, W.F.O. AU - Neubert, R. AU - Schmelz, M. AU - Schmidl, F. AU - Schwickert, M. AU - Seidel, P. AU - Sieber, T. AU - Stolz, R. AU - Stöhlker, T. AU - Tan, J. AU - Tympel, V. AU - Welsch, C.P. AU - Zakosarenko, V. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Different Versions of Cryogenic Current Comparators with Magnetic Core for Beam Current Measurements J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - For more than 20 years Cryogenic Current Comparators (CCC) are used to measure the current of charged particle beams with low intensity (nA-range). The device was first established at GSI in Darmstadt and was improved over the past two decades by the cooperation of institutes in Jena, GSI and CERN. The improved versions differ in material parameters and electronics to increase the resolution and in dimensions in order to meet the requirements of the respective application. The device allows non-destructive measurements of the charged particle beam current. The azimuthal magnetic field which is generated by the beam current is detected by low temperature Superconducting Quantum Interference Device (SQUID) current sensors. A complex shaped superconductor cooled down to 4.2 K is used as magnetic shielding and a high permeability core serves as flux concentrator. Three versions of the CCC shall be presented in this work: (1) GSI-Pb-CCC which was running at GSI Darmstadt in a transfer line, (2) CERN-Nb-CCC currently installed in the Antiproton Decelerator at CERN and (3) GSI-Nb-CCC-XD which will be operating in the CRYRING at GSI 2019. Noise, signal and drift measurements were performed in the Cryo-Detector Lab at the University of Jena. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3431 EP - 3434 KW - cryogenics KW - shielding KW - pick-up KW - operation KW - proton DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THYYPLS2 UR - http://jacow.org/ipac2019/papers/thyypls2.pdf ER - TY - CONF AU - Barth, W.A. AU - Fomichev, A.S. AU - Grigorenko, L.V. AU - Kulevoy, T. AU - Polozov, S.M. AU - Yaramyshev, S. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Charge Stripping at High Energy Heavy Ion Linacs J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - For heavy-ion accelerator facilities charge stripping is a key Technology: the stripping charge state, its efficiency to produce ions in the required charge state, and the beam quality after stripping substantially determine the entire accelerator performance. Modern heavy ion accelerator facilities such as the future Facility for Antiproton and Ion Research (FAIR) at GSI provide for high intensity heavy ion beams beyond 200 MeV/u. Heavy ion stripping at a lower energy enables more efficient acceleration up to the final beam energy, compared to acceleration of ions with a low charge state. Due to the high power deposited by the heavy ions in the stripping media and radiation damages if a solid target is used, self-recovering stripper media must be applied. General implementation options for different stripper target media are discussed in this paper, as well as general considerations to optimize the Linac layout through the appropriate choice of stripping medium and stripping energy. The driver Linac for the Dubna Electron-Radioactive Isotope Collider fAcility (DERICA) project, recently initiated by JINR, is foreseen to provide for 100 MeV/u Uranium beam in continuous wave mode. First layout scenarios of a one-step and a two-step DERICA-stripper approach will be also presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3452 EP - 3455 KW - heavy-ion KW - linac KW - target KW - acceleration KW - ion-source DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPMP005 UR - http://jacow.org/ipac2019/papers/thpmp005.pdf ER - TY - CONF AU - Ledroit, B. AU - Aulenbacher, K. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Collimation of Target Induced Halo Following MAGIX at MESA J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The Mainz Energy-recovering Superconducting Accelerator (MESA) will be an electron accelerator allowing operation in energy-recovery linac (ERL) mode. It provides the opportunity to operate scattering experiments at energies of ~100 MeV with thin gas-targets. The MESA Internal Gas Target Experiment (MAGIX) aims to operate windowless jet targets and different gases up to Xenon to search for possible dark photon interactions, to precisely measure the magnetic proton radius and astrophysical S-factors. Investigations on the impact of the target on beam dynamics and beam losses are required for machine safety and to examine limits to ERL operation. The goal of this work is to understand target induced halo in the different experimental setups, track halo particles through downstream sections to examine beam losses and include a suitable collimation system and shielding into the accelerator layout to protect the machine from direct and indirect damage through beam losses and radiation. The present status of the investigations is presented. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3839 EP - 3842 KW - target KW - simulation KW - beam-losses KW - experiment KW - cryomodule DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPRB019 UR - http://jacow.org/ipac2019/papers/thprb019.pdf ER - TY - CONF AU - Mihailescu Stoica, D. AU - Domont-Yankulova, D. AU - Klingbeil, H. AU - Lens, D.E.M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Sensitivity Analysis of Feedforward Beam Current Compensation for Improved Beam Loading Robustness J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The planned SIS100 heavy ion synchrotron at the Facility for Antiproton and Ion Research (FAIR) in Darmstadt, Germany will possess twenty ferrite accelerating cavities in its final stage of extension. During the intended acceleration cycles, the cavities will encounter significant beam loading effects, which have to be handled by the control systems. As both the generator- and beam-current act on the same system input, a feedforward disturbance compensation can be a promising approach to improve beam qualities and suppress instabilities induced by the beam current. Particle tracking simulations, incorporating twenty ferrite cavities and their attached LLRF control systems, are performed to analyse the sensitivity of the beam quality with respect to errors in the feedforward beam current compensation. The main focus lies on the time after injection from a pre-accelerator, where most cavities in the SIS100 do not provide any gap voltage and thus are particularly sensitive to induced voltages by beam currents if the cavities are not or only partly short-circuited. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3850 EP - 3852 KW - cavity KW - emittance KW - controls KW - injection KW - simulation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPRB022 UR - http://jacow.org/ipac2019/papers/thprb022.pdf ER - TY - CONF AU - Steinhagen, R.J. AU - Bräuning, H. AU - Krimm, A. AU - Milosic, T. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Redesign of the JavaFX Charts Library in View of Real-Time Visualisation of Scientific Data J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The accurate graphical representation of accelerator- or beam-based parameters is crucial for commissioning and operation in any modern accelerator. Charts are one of the most visible but at the same time often underappreciated accelerator control system components even though these are crucial for easing and improving a quick intuitive understanding of complex or large quantities of data, which in turn is used to efficiently control, troubleshoot or improve the accelerator performance. While the Java SDK and other third-party libraries provide some charting components, we found that these lack either functionality, performance, or are based on outdated complex APIs. Based on earlier GSI and CERN designs and careful analysis of missing functionalities, performance bottlenecks, and long-term maintenance risks for the necessary workarounds, we decided that it was worth to re-engineer a new scientific charting library that preserves the functionality of established other libraries while addressing the performance bottlenecks and APIs issues. The new library offers a wide variety of plot types common in the scientific community, a flexible plugin system to extend the functionality towards chart interactors as well as online parameter measurements commonly found in oscilloscopes. Tailored towards high performance, it achieves real-time update rates up to 25 Hz for data sets with a few 10k up to 5 million data points. The new API shields the complexity from and eases the library’s use by normal users, while still being modular and having explicitly open interfaces that allow more-inclined developers to modify, add or extend missing functionalities. This contribution provides a performance and functionality comparison with other existing Java-based charting libraries. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3868 EP - 3871 KW - interface KW - controls KW - real-time KW - experiment KW - framework DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPRB028 UR - http://jacow.org/ipac2019/papers/thprb028.pdf ER - TY - CONF AU - Fol, E. AU - Coello de Portugal, J.M. AU - Franchetti, G. AU - Tomás, R. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Optics Corrections Using Machine Learning in the LHC J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Optics corrections in the LHC are based on a response matrix approach between available correctors and observables. Supervised learning has been applied to quadrupole error prediction at the LHC giving promising results in simulations and surpassing the performance of the traditional approach. A comparison of different algorithms is given and it is followed by the presentation of further possible concepts to obtain optics corrections using machine learning. PB - JACoW Publishing CP - Geneva, Switzerland SP - 3990 EP - 3993 KW - optics KW - network KW - quadrupole KW - simulation KW - controls DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPRB077 UR - http://jacow.org/ipac2019/papers/thprb077.pdf ER - TY - CONF AU - Fischer, E.S. AU - Bleile, A. AU - Datskov, V.I. AU - Marusov, V. AU - Meier, J.P. AU - Spiller, P.J. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Start of the Series Production for the Cryogenic Magnet Corrector Modules of FAIR J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The fast cycling superconducting synchrotron SIS100 has to deliver high intensity beams for the FAIR project at GSI, Darmstadt. The main dipoles will ramp with 4 T/s up to a maximum magnetic field of 1.9 T where the field gradient of the main quadrupole will reach 27.77 T/m. The integral magnetic field length of the horizontal/vertical steerer and of the chromaticity sextupole will provide 0.403/0.41 m and 0.383 m respectively. We present the status of the first magnets test results as well as the overall procedure of production and testing of the complete series of the cryomagnetic corrector modules. PB - JACoW Publishing CP - Geneva, Switzerland SP - 4124 EP - 4127 KW - dipole KW - quadrupole KW - operation KW - sextupole KW - superconducting-magnet DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPTS010 UR - http://jacow.org/ipac2019/papers/thpts010.pdf ER - TY - CONF AU - Müller, H. AU - Allain, H. AU - Borceto, A. AU - Cho, E.J. AU - Daly, M. AU - Drago, G. AU - Golluccio, G. AU - Grafin, P. AU - Lucas, J. AU - Madur, A. AU - Munoz-Garcia, J.-E. AU - Quettier, L. AU - Reymond, H. AU - Roux, C. AU - Simon, H. AU - Sugita, K. AU - Valesi, G. AU - Van Den Boogaard, L.X. AU - Ventura, D. AU - Winkler, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Design, Production, and Testing of Superconducting Magnets for the Super-FRS J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The Super FRS is a two-stage in flight separator to be built next to the site of GSI, Darmstadt, Germany as part of FAIR (Facility for Anti-proton and Ion Research). Its purpose is to create and separate rare isotope beams and to enable the mass measurement also for very short lived nuclei. Due to its three branches a wide variety of experiments can be carried out in frame of the NUSTAR collaboration. Due to the large acceptance needed, the magnets of the Super-FRS have to have a large aperture and therefore only a superconducting solution is feasible. A superferric design with superconducting coils was chosen in which the magnetic field is shaped by an iron yoke. For the dipoles this iron yoke is at warm and only the coils are incorporated in a cryostat. The multiplets, assemblies of quadrupoles and higher order multipole magnets, are completely immersed in a liquid Helium bath. With the exception of special branching dipoles all superconducting magnets of Super-FRS have been contracted and are being built by Elytt in Spain (dipoles) and ASG in Italy (multiplets). The cold test of all magnets will take place in a dedicated test facility at CERN. This contribution will present the status of manufacturing of dipoles and multiplets, and also gives a short overview on the test facility. PB - JACoW Publishing CP - Geneva, Switzerland SP - 4128 EP - 4131 KW - dipole KW - quadrupole KW - cryogenics KW - octupole KW - superconducting-magnet DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPTS011 UR - http://jacow.org/ipac2019/papers/thpts011.pdf ER - TY - CONF AU - Schweizer, N. AU - Pongrac, I. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Visual Inspection of Curved Particle Accelerator Beam Pipes with a Modular Robot J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - Inspecting ultra-high vacuum pipe systems of particle accelerators without disassembling the beam pipes is a complex challenge. In particular, curved sections of particle accelerators require a unique approach for the examination of the interior. For the planned heavy ion synchrotron SIS100 at FAIR, an inspection robot is currently under development, featuring an optical imaging system with which the robot can be navigated through the beam pipe. We present the current prototype, which is based on a modular snake-like robot with active wheels and joints. Due to the stipulated low movement velocity, it can be shown that a kinematic model is sufficient to control the robot whereas dynamical effects can be neglected. This concept is proven in experiments with the prototype. At the current development status, the robot is controlled manually by setting the velocity of the first module and its desired turning angle. In simulations we include a CAD model of a dipole chamber of the SIS100 and let an operator successfully navigate the robot through the beam pipe while only observing the camera image. PB - JACoW Publishing CP - Geneva, Switzerland SP - 4135 EP - 4137 KW - controls KW - dipole KW - experiment KW - vacuum KW - simulation DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPTS014 UR - http://jacow.org/ipac2019/papers/thpts014.pdf ER - TY - CONF AU - Cho, E.J. AU - Borceto, A. AU - Drago, G. AU - Müller, H. AU - Roux, C. AU - Sugita, K. AU - Valesi, G. AU - Ventura, D. AU - Winkler, M. ED - Boland, Mark ED - Tanaka, Hitoshi ED - Button, David ED - Dowd, Rohan ED - Schaa, Volker RW ED - Tan, Eugene TI - Design and Manufacturing of the First Multiplet for the Super-FRS at FAIR J2 - Proc. of IPAC2019, Melbourne, Australia, 19-24 May 2019 CY - Melbourne, Australia T2 - International Particle Accelerator Conference T3 - 10 LA - english AB - The Super-FRS (Superconducting FRagment Separator) at FAIR is a two-stage in flight separator, which aims to produce rare isotopes of all elements up to Uranium and separate them spatially within a few hundred nanoseconds so that a study of very short lived nuclei can be performed efficiently. In total, it is required to construct 24 dipoles and 170 multipole magnets (quadrupole, sextupole, octupole and steering dipole). Due to the limit of space, the multipole magnets will be arranged as a group (2 ~ 9 magnets) in a common cryostat and they are called as a multiplet. The design challenge of the multiplet lies in a strong iron saturation of the quadrupole leading to disturb the field quality and high design pressure of the He vessel (20 bars). The first multiplet for the Super-FRS is constructed. The magnet column consisting of one quadrupole and one sextupole is cooled in a He vessel filled with up-to 800 liters of liquid He. The both magnets are superferric type and have a large warm bore radius of 190 mm. This paper presents the design overview and the manufacturing status of the first multiplet. PB - JACoW Publishing CP - Geneva, Switzerland SP - 4138 EP - 4141 KW - quadrupole KW - sextupole KW - status KW - vacuum KW - alignment DA - 2019/06 PY - 2019 SN - 978-3-95450-208-0 DO - DOI: 10.18429/JACoW-IPAC2019-THPTS015 UR - http://jacow.org/ipac2019/papers/thpts015.pdf ER -